How to Pass the AMA Exam on Your First Try
Learning how to pass the AMA exam on your first try comes down to studying the 15 ACS subject areas in proportion to their weights, mastering metallic structures and airframe inspection first, and practicing at the real 72-second-per-question pace. The test has 100 questions; you need 70 correct to pass.
Try 3 real AMA questions
Real questions from the AMA bank, with the cited explanation for every answer. Tap an answer to check it.
1. In a semimonocoque fuselage, what is the primary function of the longerons?
Semimonocoque construction reinforces the skin with longitudinal members called longerons, which extend across several frame members and help the skin support primary bending loads.
Source: Aviation Maintenance Technician Handbook—Airframe (FAA-H-8083-31B), Chapter 1, Aircraft Structures — Semimonocoque Type (p. 1-8)
2. A sheet metal repair on an aluminum airframe calls for universal-head rivets that can be driven in the as-received condition without prior heat treatment. Which rivet alloy code should the mechanic select?
The AD rivet (2117-T4) is the most frequently used repair rivet because it can be installed in the received condition. DD rivets (2024-T4) are too hard to drive as-received and must be annealed and refrigerated before installation.
Source: Aviation Maintenance Technician Handbook—Airframe (FAA-H-8083-31B), Chapter 4, Aircraft Metal Structural Repair — Rivets (p. 4-33)
3. What is the maximum continuous withdrawal rate for an acetylene cylinder?
Acetylene is limited to a maximum continuous withdrawal rate of one-seventh of the cylinder's rated capacity when full (e.g., a 330 cu ft cylinder allows 47 cu ft per hour). Faster withdrawal pulls acetone from the cylinder.
Source: Aviation Maintenance Technician Handbook—Airframe (FAA-H-8083-31B), Chapter 5, Aircraft Welding — Acetylene (p. 5-11)
Start with the format, not the textbook
Most first-try failures here are not knowledge failures. They are allocation failures: equal time on every subject, no timed practice, and the two surprise subjects left until the final week. The format tells you how to allocate.
| Test | Questions | Time | Pass score |
|---|---|---|---|
| AMG (General) | 60 | 2.0 hours | 70% (42 correct) |
| AMA (Airframe) | 100 | 2.0 hours | 70% (70 correct) |
| AMP (Powerplant) | 100 | 2.0 hours | 70% (70 correct) |
Source: FAA-G-ACS-1 Companion Guide, Ch. 3, Written Test Description table
Two numbers should shape your whole plan. First, 70 correct is the bar, a fixed standard rather than a curve, so you are measured against the standard, not against other candidates. Second, 120 minutes divided by 100 questions is 72 seconds per question. That is enough time to answer a question you know. It is not enough time to work out a bend allowance or trace a hydraulic system from half-remembered material, which is why understanding and pacing have to be trained together.
One clarification matters before you plan anything else: AMA is a single knowledge test, the Airframe written, not the A&P certificate itself. The full certificate takes all three writtens plus the oral and practical exams for each rating (FAA-G-ACS-1 Companion Guide, Ch. 1).
To sit for the test, you need an authorization document, either an authenticated document from an FAA-approved Aviation Maintenance Technician School, or an FAA Form 8610-2 endorsed by a Flight Standards District Office (FAA-G-ACS-1 Companion Guide, Ch. 4). Sort that path out early, so paperwork does not become a test-week problem.
Study in proportion to the 15 ACS subject areas
The AMA samples 15 subject areas defined in Section II of the Airman Certification Standards, FAA-S-ACS-1 (FAA-G-ACS-1 Companion Guide). The FAA publishes weight bands for the test, and your study hours should follow them, not the order chapters happen to appear in a handbook.
| Subject area | Share of the test | Study priority |
|---|---|---|
| Metallic Structures | 5–15% | Highest |
| Airframe Inspection | 5–15% | Highest |
| Non-Metallic Structures | 5–10% | High |
| Flight Controls | 5–10% | High |
| Landing Gear Systems | 5–10% | High |
| Hydraulic and Pneumatic Systems | 5–10% | High |
| Environmental Systems | 5–10% | High |
| Aircraft Instrument Systems | 5–10% | High |
| Communication and Navigation Systems | 5–10% | High |
| Aircraft Fuel Systems | 5–10% | High |
| Aircraft Electrical Systems | 5–10% | High |
| Ice and Rain Control Systems | 5–10% | High |
| Airframe Fire Protection Systems | 5–10% | High |
| Rotorcraft Fundamentals | 5–10% | High, the surprise topic |
| Water and Waste Systems | 5–10% | High, the other surprise topic |
Source: FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table; subject list per FAA-S-ACS-1, Section II.
On a 100-question test, a 5–15% band can mean up to 15 questions from one area. That math is the whole argument for weighted studying: a weak performance in Metallic Structures or Airframe Inspection alone can use up half of the 30 questions you are allowed to miss. The table also settles a common mistake: Rotorcraft Fundamentals and Water and Waste Systems are real, separate Airframe subjects, each at 5–10%, even if your training was all fixed-wing work.
The official study source is the FAA Aviation Maintenance Technician Handbook — Airframe, FAA-H-8083-31B. Use it to learn a subject, then use questions to prove you can apply it.
A six-week plan that follows the weights
This plan assumes a base from school or shop experience. If you are starting colder, stretch the middle weeks rather than compressing the last ones.
Week 1 — Baseline and metallic structures. Take a timed diagnostic before you study anything, and record your score by subject area, not just your total. Then start Metallic Structures, one of the two 5–15% areas: rivet identification and spacing, alloy designations, bend allowance, and corrosion. A diagnostic first stops you re-reading subjects you already know.
Week 2 — Non-metallic structures and flight controls. Work Non-Metallic Structures together with Flight Controls. Learn composites, wood, and fabric covering as materials with specific inspection and repair rules, then move to control surfaces, cable tension, and rigging. These areas reward clear pictures in your head, so draw structures and trace control runs instead of only reading about them.
Week 3 — Airframe inspection plus landing gear and hydraulics. Airframe Inspection is the other 5–15% area, so it anchors this week. Study inspection types and scopes alongside Landing Gear Systems and Hydraulic and Pneumatic Systems, the systems inspection questions point at most often. Learn each system by following what flows or moves through it, and drill each area as you finish it.
Week 4 — Fuel, electrical, and instruments. Move through Aircraft Fuel Systems, Aircraft Electrical Systems, and Aircraft Instrument Systems as one connected cluster. A fuel quantity indication, a bus fault, and an instrument reading are often the same story told from different ends, and questions cross between these areas.
Week 5 — Environmental, communication, protection, and the surprise subjects. Work Environmental Systems, Communication and Navigation Systems, Ice and Rain Control Systems, and Airframe Fire Protection Systems. Then give Rotorcraft Fundamentals and Water and Waste Systems their own focused sessions. Each of these areas is 5–10% of the test (FAA-G-ACS-1 Companion Guide), and the last two are where fixed-wing candidates most often leave points behind.
Week 6 — Timed simulations and weak-spot repair. Take full 100-question practice runs under the real 2-hour limit, in one sitting, with no pausing. Review every miss by subject area, re-study that subject in FAA-H-8083-31B, and re-drill it. Your last sessions should be light review of your weakest areas, not a first read of anything new.
If your diagnostic shows one area far below the others, move it earlier: learn it as a connected story, drill it, and revisit it a week later.
Build a 72-second-per-question reflex
Pacing is a skill you can practice, and on this test it is worth real points: well under a minute for a straightforward recall question, and more for a calculation or systems question, banked from the questions you answered quickly.
Use this routine in every timed practice session:
- Answer the question in front of you. Do not skip around hunting for easy questions first; each question is independent, with a single correct response (FAA-G-ACS-1 Companion Guide, Ch. 3).
- If a question is not coming together after about 90 seconds, mark it, choose your best current answer, and move on. A marked question you return to costs you nothing. An unanswered block at the end because the clock ran out costs you several.
- Return to marked questions with the time you banked. Recheck the underlying logic first, the rivet spacing rule, the inspection scope, or the system path, rather than trying to relearn a subject on the clock.
- Leave a final check pass if you finish early. Use it only for marked questions and for questions you rushed, not to second-guess answers you were confident about.
Practice with the testing supplement as well, so test day is not your first time working from its figures.
Learn structures and systems as stories, not lists
Reading a definition and using it under time are different skills. The AMA's hardest questions ask what happens when one part of a structure or system is damaged, worn, or mis-rigged, and the effect often shows up in a different subject area than the cause. Every question is still objective multiple-choice with a single correct response (FAA-G-ACS-1 Companion Guide, Ch. 3), but the right response often depends on tracing a chain.
For each subject, study in this order: first the layout, what connects to what and in what order; then the failure and wear modes, what each one looks like on inspection; then mixed questions under time, where you have to recognize which system a symptom belongs to. Work the connections deliberately: corrosion against structural strength, cable tension against control feel, hydraulic pressure against gear and flap operation. Most candidates stop at the parts list. The second and third steps are what transfer to test day.
The mistakes that cost first-time candidates
Studying every subject equally. Fifteen areas do not carry equal weight. Equal time quietly underfunds Metallic Structures and Airframe Inspection, the two areas that can each reach 15% of the test (FAA-G-ACS-1 Companion Guide).
Only reading, never testing. A handbook pass-through feels productive and proves very little. Timed questions expose the gap between recognizing material and producing an answer, the gap the exam measures.
Skipping the surprise subjects. Rotorcraft Fundamentals and Water and Waste Systems are each 5–10% of this test (FAA-G-ACS-1 Companion Guide). Candidates who skip them because their experience never covered them start the test effectively 10 to 20 questions down.
Memorizing structures without working problems. Metallic Structures questions ask you to apply spacing, edge distance, and bend rules, not just name them. Work examples until the calculation is routine, then do it under time.
Treating a fail as the end of the path. It is not. Your Airman Knowledge Test Report lists the ACS codes for the areas you missed, and you may retest after 30 days, or sooner if you present a signed statement from an airman holding the certificate and rating you are seeking, certifying that you received additional instruction in each subject you failed and are considered ready for retesting (14 CFR 65.19). A focused plan built on those codes is a stronger position than most first-time candidates start from.
How to know you are ready
Do not judge readiness by how the material feels when you re-read it. Judge it by timed performance: you finish a full 100-question run inside 2 hours, your marked questions are a small minority, and your misses are spread out rather than concentrated in one area. Concentration is the warning sign, because one weak 5–15% area can account for up to 15 questions (FAA-G-ACS-1 Companion Guide), half of everything you are allowed to miss.
When a run shows a concentrated weakness, pause, re-study that subject, drill it, and test again. That loop is the entire method.
What this article can't do for you
A study plan can tell you how the AMA is weighted and how to pace it. It cannot tell you which of the 15 subject areas you are weak in, or whether your structures knowledge holds up under a 72-second clock. That takes a timed run against real-style questions, with explanations that show you why an answer is right, so your weak areas show up as data, not as a surprise in your score report.
See where you stand: Upward Prep's free 25-question AMA practice test mirrors the ACS subject weights, times you like the real thing, and gives cited explanations for every answer. It is the fastest way to turn this plan into your plan, starting with the subject you most need to fix. Try the free AMA practice test →
Frequently asked questions
how many questions
There are 100 multiple-choice questions on the AMA, with a 2.0-hour time limit and a 70% passing score, which means 70 correct answers (FAA-G-ACS-1 Companion Guide, Ch. 3). That works out to 72 seconds per question, which is why this plan trains pacing alongside content.
what is on the airframe exam
The Airframe exam samples 15 ACS subject areas: Metallic Structures, Non-Metallic Structures, Flight Controls, Airframe Inspection, Landing Gear Systems, Hydraulic and Pneumatic Systems, Environmental Systems, Aircraft Instrument Systems, Communication and Navigation Systems, Aircraft Fuel Systems, Aircraft Electrical Systems, Ice and Rain Control Systems, Airframe Fire Protection Systems, Rotorcraft Fundamentals, and Water and Waste Systems (FAA Aviation Mechanic ACS, FAA-S-ACS-1, Section II). Metallic Structures and Airframe Inspection carry the heaviest weight bands, at 5–15% each (FAA-G-ACS-1 Companion Guide).
ama practice test
Use a practice test the way this plan uses the Week 1 diagnostic and the Week 6 simulations: timed, in one sitting, and reviewed by subject area afterward. A practice score by itself does not tell you what to study next; the pattern of your misses across the 15 ACS areas does (FAA-G-ACS-1 Companion Guide). Start with the free 25-question test linked above, then aim your study at the areas it flags.
ama test breakdown
The breakdown is 100 questions drawn from 15 subject areas, with published weight bands: Metallic Structures and Airframe Inspection at 5–15% each, and the other thirteen areas at 5–10% each (FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table). You have 2.0 hours and need 70% to pass (FAA-G-ACS-1 Companion Guide, Ch. 3). Your study hours should follow those bands, which is how the six-week plan above is built.
what happens if you fail the airframe written
You receive an Airman Knowledge Test Report listing the ACS codes for the subjects you missed, which becomes your restudy list. You may apply for retesting after 30 days, or before those 30 days have expired if you present a signed statement from an airman holding the certificate and rating you are seeking, certifying that you received additional instruction in each subject you failed and are considered ready for retesting (14 CFR 65.19).
