What's Actually on the AMA Exam: Subject-by-Subject Breakdown

What is on the AMA exam is 100 multiple-choice questions drawn from 15 subject areas in Section II of the FAA Aviation Mechanic Airman Certification Standards: structures, flight controls, inspection, and twelve aircraft systems areas, ending with rotorcraft fundamentals and water and waste systems (FAA-G-ACS-1 Companion Guide).

Try 3 real AMA questions

Real questions from the AMA bank, with the cited explanation for every answer. Tap an answer to check it.

1. In a semimonocoque fuselage, what is the primary function of the longerons?

2. A sheet metal repair on an aluminum airframe calls for universal-head rivets that can be driven in the as-received condition without prior heat treatment. Which rivet alloy code should the mechanic select?

3. What is the maximum continuous withdrawal rate for an acetylene cylinder?

Where does this breakdown come from?

It comes from the FAA's own publications, not from a prep company's guess. The subject areas are the 15 knowledge areas in Section II of the Aviation Mechanic ACS, FAA-S-ACS-1, and the Companion Guide to that standard, FAA-G-ACS-1, publishes both the written test description and the percentage of test questions each area carries (FAA-G-ACS-1 Companion Guide).

The AMA is the Airframe test, one of the three FAA written tests on the way to an Airframe and Powerplant certificate. Its full format, next to the other two writtens, is:

Test Questions Time Pass score
AMG (General) 60 2.0 hours 70% (42 correct)
AMA (Airframe) 100 2.0 hours 70% (70 correct)
AMP (Powerplant) 100 2.0 hours 70% (70 correct)

Source: FAA-G-ACS-1 Companion Guide, Ch. 3, Written Test Description table

One clarification clears up a common confusion: the AMA is a single knowledge test for the airframe rating. It is not the A&P certificate itself. The full certificate takes the three writtens plus oral and practical exams with a Designated Mechanic Examiner for each rating (FAA-G-ACS-1 Companion Guide, Ch. 1).

What are the 15 subject areas at a glance?

Here is the whole test on one table: each ACS subject area, the share of the test the FAA assigns it, and what that share means in questions on a 100-question test.

Subject area Share of the test Questions (of 100)
Metallic Structures 5–15% 5–15
Airframe Inspection 5–15% 5–15
Non-Metallic Structures 5–10% 5–10
Flight Controls 5–10% 5–10
Landing Gear Systems 5–10% 5–10
Hydraulic and Pneumatic Systems 5–10% 5–10
Environmental Systems 5–10% 5–10
Aircraft Instrument Systems 5–10% 5–10
Communication and Navigation Systems 5–10% 5–10
Aircraft Fuel Systems 5–10% 5–10
Aircraft Electrical Systems 5–10% 5–10
Ice and Rain Control Systems 5–10% 5–10
Airframe Fire Protection Systems 5–10% 5–10
Rotorcraft Fundamentals 5–10% 5–10
Water and Waste Systems 5–10% 5–10

Source: FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table; subject list per FAA-S-ACS-1, Section II, subjects A to O.

Two things are worth noticing. First, the bands are ranges, not fixed counts: the FAA builds each test form inside these percentages, so your form's exact split will differ slightly from another candidate's. Second, this is the broadest of the three writtens. Fifteen areas means no single topic dominates, and a plan that ignores the small areas gives away real points: thirteen areas at up to 10 questions each is most of the test.

An older topic list still circulates in some study material, naming subjects such as aircraft fabric covering, aircraft finishes, welding, and assembly and rigging as separate areas. That was the retired Practical Test Standards list, not the current ACS list above. If your material is organized around those old headings, map it back to the 15 ACS areas before you trust its coverage.

The structures cluster: metallic, non-metallic, flight controls, and inspection

Four areas cover the airframe itself: what it is built from, how it moves, and how you check its condition.

Metallic Structures (5–15%) is tied for the heaviest area on the test (FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table). This is the sheet metal core of the exam: rivet layouts, bend allowances, alloy work, and corrosion, covered in the FAA airframe handbook's chapters on aircraft structures and aircraft metal structural repair (FAA-H-8083-31B, Vol. 1, Ch. 1 and Ch. 4). Questions here ask you to apply spacing, edge distance, and bend rules, not just name them, so worked examples matter more than re-reading.

Non-Metallic Structures (5–10%) covers the other construction materials: wood, fabric covering, and composites, in the handbook's chapters on aircraft fabric covering, aircraft wood and structural repair, and advanced composite materials (FAA-H-8083-31B, Vol. 1, Ch. 3, Ch. 6, and Ch. 7). Learn each material as a set of inspection and repair rules, because the questions test which rule belongs to which material.

Flight Controls (5–10%) covers control surfaces, cables, rigging, and assembly, the material in the handbook chapter on aerodynamics, aircraft assembly, and rigging (FAA-H-8083-31B, Vol. 1, Ch. 2). This area rewards a clear picture of how a control run connects, from the cockpit to the surface, because questions often start from a symptom in feel or movement and ask where the fault sits.

Airframe Inspection (5–15%) is the other heavyweight (FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table). It tests inspection types, scopes, and what an inspection is supposed to find, and it connects to every other area: the structures and systems above are what you are inspecting. Study it after you have a base in structures and systems, and it stops being abstract.

The systems cluster: gear, hydraulics, fuel, electrical, and the rest

Eight areas cover the aircraft systems that sit inside the airframe. Each is 5–10% of the test (FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table), and together they are the largest block of questions on the exam.

Landing Gear Systems covers struts, brakes, wheels, and tires, in the handbook's aircraft landing gear systems chapter (FAA-H-8083-31B, Vol. 2, Ch. 13).

Hydraulic and Pneumatic Systems covers fluid power: pumps, actuators, valves, and reservoirs, in the handbook's hydraulic and pneumatic power systems chapter (FAA-H-8083-31B, Vol. 2, Ch. 12). Learn each system by tracing what flows through it, in order. That tracing habit is what the application questions measure.

Environmental Systems covers cabin environmental control, including pressurization, heating, air conditioning, and oxygen, in the handbook's cabin environmental control systems chapter (FAA-H-8083-31B, Vol. 2, Ch. 16).

Aircraft Instrument Systems and Communication and Navigation Systems are a pair: instruments in the handbook's aircraft instrument systems chapter, and radios and navigation in its communication and navigation chapter (FAA-H-8083-31B, Vol. 2, Ch. 10 and Ch. 11).

Aircraft Fuel Systems covers tanks, cells, delivery, and contamination and fueling safety, in the handbook's aircraft fuel system chapter (FAA-H-8083-31B, Vol. 2, Ch. 14).

Aircraft Electrical Systems covers batteries, generation, wiring, and circuit protection, starting in the handbook's aircraft electrical system chapter in Volume 1 (FAA-H-8083-31B, Vol. 1, Ch. 9). This is one of the systems areas where calculation and circuit reasoning return, so work problems, not just definitions.

The honest way to handle eight mid-weight systems is one at a time, in the same order every time: layout first, then normal operation, then failure and wear signs, then questions under time. Skipping that order is how candidates end up recognizing a system on the page but unable to answer what happens when a component in it fails.

The protection areas and the two surprise subjects

Ice and Rain Control Systems (5–10%) covers anti-ice, de-ice, and rain removal, in the handbook's ice and rain protection chapter (FAA-H-8083-31B, Vol. 2, Ch. 15).

Airframe Fire Protection Systems (5–10%) covers fire detection and extinguishing, in the handbook's fire protection systems chapter, the closing chapter of Volume 2 (FAA-H-8083-31B, Vol. 2, Ch. 17).

Rotorcraft Fundamentals (5–10%) and Water and Waste Systems (5–10%) are the two areas candidates most often skip, because many training paths are fixed-wing focused and neither topic fills a handbook chapter of its own in the same way the systems above do. They are still real, separate ACS subjects, each worth up to 10 questions (FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table). Starting the test effectively 10 to 20 questions down, out of only 30 you are allowed to miss, is an avoidable handicap. Give both a focused session each, even if your experience never covered them.

How should you use these weights to study?

Study in proportion, and let the arithmetic set your priorities. You need 70 of 100 correct, so you can miss 30 questions (FAA-G-ACS-1 Companion Guide, Ch. 3). A single weak heavy area at the top of the 5–15% band can account for 15 of those 30 misses by itself. That is why Metallic Structures and Airframe Inspection get the largest shares of your time, why structures work gets worked problems rather than re-reading, and why no 5–10% area gets zero time: the thirteen smaller areas together are most of your score.

Pacing follows the same math. 120 minutes for 100 questions is 72 seconds per question (FAA-G-ACS-1 Companion Guide, Ch. 3). Recall questions should take less, banking time for bend allowance calculations and system tracing questions. Practicing by subject area, under time, is how you find out whether your personal split matches the FAA's published one, or whether one area is quietly eating your margin.

What this article can't do for you

This breakdown tells you what the exam contains and how it is weighted. It cannot tell you where you stand inside it. Two candidates can both read that metallic structures is up to 15% of the test and be in opposite positions: one solid on structures and weak on electrical, the other the reverse. Reading the weights does not reveal your own pattern of misses, and guessing at it wastes the study time this article just helped you allocate.

That is what a diagnostic is for. Upward Prep's free 25-question AMA practice test mirrors the ACS subject weights, times you like the real thing, and gives cited explanations for every answer, so you can put your hours into the subject areas that are actually costing you points. Try the free AMA practice test →

Frequently asked questions

what is on the airframe exam

The Airframe exam, the AMA, is 100 multiple-choice questions drawn from 15 ACS subject areas: Metallic Structures, Non-Metallic Structures, Flight Controls, Airframe Inspection, Landing Gear Systems, Hydraulic and Pneumatic Systems, Environmental Systems, Aircraft Instrument Systems, Communication and Navigation Systems, Aircraft Fuel Systems, Aircraft Electrical Systems, Ice and Rain Control Systems, Airframe Fire Protection Systems, Rotorcraft Fundamentals, and Water and Waste Systems (FAA-G-ACS-1 Companion Guide).

airframe test topics

The topic list is the 15 areas above, and the FAA airframe handbook, FAA-H-8083-31B, covers them across its two volumes, from Aircraft Structures and Aircraft Metal Structural Repair in Volume 1 to Hydraulic and Pneumatic Power Systems, Aircraft Landing Gear Systems, and Fire Protection Systems in Volume 2 (FAA-H-8083-31B, tables of contents). If a topic you are studying does not map to one of the 15 ACS areas, it is probably material for the General or Powerplant test instead.

ama test breakdown

Two areas carry 5–15% of the test each: Metallic Structures and Airframe Inspection. The other thirteen areas carry 5–10% each (FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table). On 100 questions, that works out to roughly 5–15 questions from each heavy area and 5–10 from each of the rest.

systems on the airframe exam

Eight of the 15 areas are aircraft systems: Landing Gear, Hydraulic and Pneumatic, Environmental, Aircraft Instrument, Communication and Navigation, Aircraft Fuel, Aircraft Electrical, and the protection pair, Ice and Rain Control and Airframe Fire Protection (FAA-G-ACS-1 Companion Guide). Together, at 5–10% each, they make up the largest block of the test, which is why systems study should follow one repeatable method: layout, operation, failure signs, then timed questions.

how many questions

There are 100 questions on the AMA, with a 2.0-hour time limit and a 70% passing score, which means 70 correct answers and 72 seconds per question (FAA-G-ACS-1 Companion Guide, Ch. 3). The General test before it is shorter, at 60 questions, and the Powerplant test is also 100 questions, both with the same 2.0-hour limit and 70% bar (FAA-G-ACS-1 Companion Guide, Ch. 3).