How to Pass the AMG Exam on Your First Try
Learning how to pass the AMG exam on your first try comes down to three things: study the 12 ACS subject areas in proportion to their weights, drill electricity and weight-and-balance calculations until they are automatic, and practice under the real 2-hour limit. The test has 60 questions; you need 42 correct.
Try 3 real AMG questions
Real questions from the AMG bank, with the cited explanation for every answer. Tap an answer to check it.
1. A 28-volt DC circuit contains a single 7-ohm resistor. How much current flows in the circuit?
Ohm's Law states current equals voltage divided by resistance (I = E/R). 28 volts ÷ 7 ohms = 4 amperes.
Source: Aviation Maintenance Technician Handbook—General (FAA-H-8083-30B), Chapter 12, Fundamentals of Electricity & Electronics, Ohm's Law (Resistance)
2. An aircraft cabin light draws 5 amperes from the 28-volt DC bus. How much electrical power does the light consume?
Electrical power equals voltage multiplied by current (P = E × I, Watt's Law). 28 volts × 5 amperes = 140 watts.
Source: Aviation Maintenance Technician Handbook—General (FAA-H-8083-30B), Chapter 12, Fundamentals of Electricity & Electronics, Power and Energy / Power Formulas
3. Three resistors of 10 ohms, 20 ohms, and 30 ohms are connected in series across a voltage source. What is the total resistance of the circuit?
In a series circuit, total resistance is the sum of the individual resistances: 10 + 20 + 30 = 60 ohms.
Source: Aviation Maintenance Technician Handbook—General (FAA-H-8083-30B), Chapter 12, Fundamentals of Electricity & Electronics, Series Circuits / Resistance in Series
Start with the format, not the textbook
Most first-try failures are not knowledge failures. They are allocation failures: equal time on every chapter, no timed practice, and too little work on the calculation subjects. The format tells you how to allocate.
| Test | Questions | Time | Pass score |
|---|---|---|---|
| AMG (General) | 60 | 2.0 hours | 70% (42 correct) |
| AMA (Airframe) | 100 | 2.0 hours | 70% (70 correct) |
| AMP (Powerplant) | 100 | 2.0 hours | 70% (70 correct) |
Source: FAA-G-ACS-1 Companion Guide, Ch. 3, Written Test Description table
Two numbers should shape your whole plan. First, 42 correct is the bar — a fixed 70% standard, not a curve, so you are measured against the standard and not against other candidates. Second, 120 minutes divided by 60 questions is 2 minutes per question. That is generous for a recall question and tight for a multi-step calculation, which is why pacing and calculation speed, not just reading, have to be trained.
To sit for the test, you need an authorization document — either an authenticated document from an FAA-approved Aviation Maintenance Technician School, or an FAA Form 8610-2 endorsed by a Flight Standards District Office (FAA Airman Knowledge Testing Matrix). Confirm you have that path sorted early, so a paperwork problem does not become a test-week problem.
Study in proportion to the 12 ACS subject areas
The AMG samples 12 subject areas defined in the Airman Certification Standards (FAA-S-ACS-1, Section I) (FAA-G-ACS-1 Companion Guide). The FAA publishes weight bands for the test, and your study hours should follow them — not the order chapters happen to appear in a handbook.
| Subject area | Share of the test | Study priority |
|---|---|---|
| Basic Electricity | 5–15% | Highest — calculation-heavy |
| Ground Operations and Servicing | 5–15% | Highest |
| Aircraft Drawings | 5–10% | High |
| Weight and Balance | 5–10% | High — calculation-heavy |
| Fluid Lines and Fittings | 5–10% | High |
| Materials and Hardware | 5–10% | High |
| Cleaning and Corrosion Control | 5–10% | High |
| Mathematics | per ACS weights | Foundation — do first |
| Physics | per ACS weights | Foundation |
| Inspection Concepts and Techniques | per ACS weights | Core |
| Regulations | per ACS weights | Core |
| Human Factors | per ACS weights | Core |
Source: FAA-G-ACS-1 Companion Guide, percentage-of-test-questions table; subject list per FAA-S-ACS-1, Section I.
On a 60-question test, a 5–15% band can mean up to 9 questions from one area. That math is the whole argument for weighted studying: a weak performance in Basic Electricity alone can use up most of the 18 questions you are allowed to miss. The official study source for these areas is the FAA Aviation Maintenance Technician Handbook — General, FAA-H-8083-30B, which covers mathematics, physics, weight and balance, materials and hardware, cleaning and corrosion control, fluid lines and fittings, inspection concepts, fundamentals of electricity and electronics, regulations, ground operations, and human factors (FAA-H-8083-30B, Aviation Maintenance Technician Handbook — General). Use the handbook to learn a subject, then use questions to prove you can apply it.
A six-week plan that follows the weights
This plan assumes you already have a base from school or shop experience and can study most days. If you are starting colder — especially on electricity or algebra — stretch the first three weeks rather than compressing the last ones. The sequence matters more than the calendar.
Week 1 — Baseline and foundations. Take a timed diagnostic before you study anything, and record your score by subject area, not just your total. Then start Mathematics and Physics: the arithmetic, area and ratio work, and basic physics ideas that the calculation subjects build on. A diagnostic first stops you spending Week 1 re-reading subjects you already know.
Week 2 — Basic Electricity, part one. Work Ohm's law and power until the calculations are routine, then series and parallel circuits. This is the heaviest and most calculation-dense area, so it gets two passes, not one. Do problems on paper, showing each step, the way you will have to work them at the testing center.
Week 3 — Weight and Balance plus Basic Electricity, part two. Add weight-and-balance calculations — weight, arm, and moment — alongside a second electricity pass focused on the question types you missed in Week 2. By the end of this week, the two calculation clusters that decide most close results should feel familiar, even if they are not fast yet.
Week 4 — The 5–10% band. Move through Aircraft Drawings, Fluid Lines and Fittings, Materials and Hardware, and Cleaning and Corrosion Control. These areas reward steady, complete coverage: learn the terms, the hardware identification, and the procedures, and drill each area as you finish it rather than saving all questions for the end.
Week 5 — Ground Operations, Inspection, Regulations, and Human Factors. Ground Operations and Servicing carries the other 5–15% band, so give it a full share of this week, not leftovers. Then work Inspection Concepts and Techniques, Regulations, and Human Factors. Regulations questions are learnable and specific — read the rule, then answer questions on that rule while it is fresh.
Week 6 — Timed simulations and weak-spot repair. Take full 60-question practice runs under the real 2-hour limit, in one sitting, with no pausing. Review every miss by subject area, re-study that subject in FAA-H-8083-30B, and then re-drill it. Your last sessions should be light review of your weakest areas and your calculation routines — not a first read of anything new.
If your diagnostic in Week 1 shows one area far below the others, do not follow this calendar rigidly. Move that area earlier and give it the Week 2 treatment: learn it, drill it, and revisit it a week later. The plan is a default, not a contract.
Build a 2-minute-per-question reflex
Pacing is a skill you can practice, and on this test it is worth real points. Two minutes per question breaks down simply: about a minute to read and answer a straightforward question, and more for a calculation — banked from the questions you answered quickly.
Use this routine in every timed practice session:
- Answer the question in front of you. Do not skip around hunting for easy questions first; each question is independent, with a single correct response (FAA-G-ACS-1 Companion Guide, Ch. 3).
- If a calculation is not coming together after about 2 minutes, mark it, choose your best current answer, and move on. A marked question you return to costs you nothing. An unanswered block at the end because the clock ran out costs you several.
- Return to marked questions with the time you banked. Recheck the arithmetic first — a dropped sign or a misread unit is a cheaper fix than relearning a subject.
- Leave a final check pass if you finish early. Use it only for marked questions and for calculations you rushed, not to second-guess answers you were confident about.
Practice with the testing supplement as well. The written test uses the FAA-CT-8080-4G testing supplement, a booklet of figures and diagrams you reference during the exam (FAA Airman Knowledge Testing Matrix). If the first time you open it is test day, you will spend test minutes learning how it is organized instead of answering questions.
Drill the calculations until they are automatic
Reading about a formula and using it under time are different skills. The AMG's calculation questions — in Basic Electricity, Weight and Balance, Mathematics, and Physics — have exactly one right answer and no partial credit, because every question is objective multiple-choice with a single correct response (FAA-G-ACS-1 Companion Guide, Ch. 3).
For each calculation type, work in this order: worked examples from the handbook, copying the steps by hand; short sets of the same problem type until the setup is automatic; then mixed sets under time, where you have to recognize which method a question needs. Most candidates stop after the first step — the third step is the one that transfers to test day. Show your work every time: written steps are how you catch an arithmetic slip in your check pass.
The mistakes that cost first-time candidates
Studying every subject equally. Twelve areas do not carry equal weight. Equal time quietly underfunds Basic Electricity and Ground Operations and Servicing, the two areas that can each reach 15% of the test (FAA-G-ACS-1 Companion Guide).
Only reading, never testing. A handbook pass-through feels productive and proves very little. Timed questions expose the gap between recognizing material and producing an answer, which is the gap the exam measures.
Ignoring a weak diagnostic area. A low score in one subject in Week 1 is useful information, not a verdict. It becomes a problem only if your plan does not change because of it.
Cramming calculations the final week. Calculation speed builds over repeated sessions. A final-week sprint can refresh formulas, but it cannot build the automatic step-by-step routine that Week 2 and Week 3 work builds.
Treating a fail as the end of the path. It is not. Your Airman Knowledge Test Report lists the ACS codes for the areas you missed, and you may retest after 30 days, or sooner if you present a signed statement from an airman holding the certificate and rating you are seeking, certifying that you received additional instruction in each subject you failed and are considered ready for retesting (14 CFR 65.19). A focused plan built on those codes is a stronger position than most first-time candidates start from.
How to know you are ready
Do not judge readiness by how the material feels when you re-read it. Judge it by timed performance: you can finish a full 60-question run inside 2 hours, your marked questions are a small minority, and your misses are spread out rather than concentrated in one subject area. Concentration is the warning sign — on the real test, one weak 5–15% area can account for up to 9 questions (FAA-G-ACS-1 Companion Guide).
When a timed run shows a concentrated weakness, pause the simulations, go back to that subject in the handbook, drill it, and test again. That loop — test, identify, study, retest — is the entire method.
What this article can't do for you
A study plan can tell you how the AMG is weighted and how to pace it. It cannot tell you which of the 12 subject areas you are weak in, or whether your electricity calculations hold up under a clock. That takes a timed run against real-style questions, with explanations that show you why an answer is right — so your weak areas show up as data you can act on, not as a surprise in your score report.
See where you stand: Upward Prep's free 25-question AMG practice test mirrors the ACS subject weights, times you like the real thing, and gives cited explanations for every answer. It is the fastest way to turn this plan into your plan, starting with the subject you most need to fix. Try the free AMG practice test →
Frequently asked questions
how many questions
There are 60 multiple-choice questions on the AMG, with a 2.0-hour time limit and a 70% passing score, which means 42 correct answers (FAA-G-ACS-1 Companion Guide, Ch. 3). That works out to 2 minutes per question, which is why this plan trains pacing alongside content.
what is on the general exam
The General exam samples 12 ACS subject areas: Mathematics, Physics, Basic Electricity, Aircraft Drawings, Weight and Balance, Fluid Lines and Fittings, Materials and Hardware, Cleaning and Corrosion Control, Inspection Concepts and Techniques, Regulations, Human Factors, and Ground Operations and Servicing (FAA Aviation Mechanic ACS, FAA-S-ACS-1, Section I). Basic Electricity and Ground Operations and Servicing carry the heaviest weight bands, at 5–15% each (FAA-G-ACS-1 Companion Guide).
amg practice test
Use a practice test the way this plan uses the Week 1 diagnostic and the Week 6 simulations: timed, in one sitting, and reviewed by subject area afterward. A practice score by itself does not tell you what to study next — the pattern of your misses across the 12 ACS areas does (FAA-G-ACS-1 Companion Guide). Start with the free 25-question test linked above, then aim your study at the areas it flags.
do i take general first
For most candidates seeking both ratings, the General comes first in the three-writtens sequence, before the Airframe and Powerplant tests. The AMG has 60 questions, while the Airframe and Powerplant tests have 100 questions each, all with a 2.0-hour limit and a 70% passing score (FAA-G-ACS-1 Companion Guide, Ch. 3). Passing the shortest test first also gives you a real score report and a proven study routine to carry into the longer tests.
what happens if you fail
You receive an Airman Knowledge Test Report listing the ACS codes for the subjects you missed, which becomes your restudy list. You may apply for retesting after 30 days, or before those 30 days have expired if you present a signed statement from an airman holding the certificate and rating you are seeking, certifying that you received additional instruction in each subject you failed and are considered ready for retesting (14 CFR 65.19).
